Behringer Introduces "SC" Cutting Technology -- Faster Cutting & Improved Productivity With Longer Blade Life
Behringer, a world-class provider of bandsawing machines, circular cold saws and structural fabricating equipment, has expanded its HBM series of high-performance bandsaws to include the new HBM-SC series. The HBM440A-SC and HBM540A-SC feature SC (speed cutting) technology which enables ultra high-speed cutting of virtually all metals including tool steels, stainless steel and other materials traditionally presenting slow cut rates.
Morgantowm, PA (PRWEB) -- Behringer, a world-class provider of bandsawing machines, circular cold saws and structural fabricating equipment, has expanded its HBM series of high-performance bandsaws to include the new HBM-SC series. The HBM440A-SC and HBM540A-SC feature SC (speed cutting) technology which enables ultra high-speed cutting of virtually all metals including tool steels, stainless steel and other materials traditionally presenting slow cut rates.
Productivity tests conducted at Behringer showed that conventional band sawing machines with bimetal saw blades can cut solid chromium-manganese material with a diameter of 6" at a rate of about 12 sq. in./min. Adding a carbide-tipped blade boosts this rate to about 20 sq. in./min. With SC technology installed, the approximate cut rate achieved in the tests was near 77.5 sq. in./min which is more than quadruple the rate of a conventional bandsaw.
"In plain terms," said Richard Klipp, Behringer president, "a single bandsaw with SC installed can make a cut in about a half a minute whereas a conventional bandsaw might take up to two minutes. One of our saws with SC technology can probably out-produce three standard machine saws partly because there is a much higher volume of filtered flood coolant used, and also because the chip removal system is capable of handling massive amounts of debris."
To maximize cutting speed capability Behringer has dynamically re-engineered the HBM saw frame so that it channels the buildup of forces away from the work area. This permits optimized band clamping to reduce vibration and increase precision movement. Newly designed band guides are fitted with nozzles which spray coolant directly into the kerf. Coupled with a high volume coolant pump, this keeps blades and materials as cool as possible during high speed cutting enabling longer periods of uninterrupted throughput when compared to conventional bandsaws.
The HBM-SC sawing blade downfeed is driven by a ball screw powered with a heavy-duty gearbox and a high horsepower motor with a torque drive of 35 HP. This provides the controlled application of downfeed power required for precise, accurate movement of the blade through the material being cut.
Downfeed power is then balanced against blade wear via a blade pressure monitor which is linked to a servo-controlled cutting pressure sensing system. This power/pressure balance assures that the material feed rate is always maximized without overloading the blade. This results in the longest possible blade life.
Because SC technology yields higher rates of stock removal, an unusually high volume of chips are produced. Two self-adjusting brushes clean the saw band while the saw operates. Falling into a funnel shaped flume, the chips are guided to a dual conveyor in the machine bed. This is a high capacity, high efficiency chip removal system allowing operators to achieve and maintain high productivity levels without being forced to stop work in order to clear the work area.
For more information on the HBM-SC series high-performance bandsaws with SC cutting technology contact Behringer Saws, Inc., 721 Hemlock Road, Morgantown, PA 19543. Call toll-free at 888-234-7464.
About Behringer Saws
Behringer Saws, Inc. provides a full range of sawing and turnkey pre- and post-cut material handling productivity-enhancing products. Behringer supplies world-class quality automatic bandsaws to corporations, service centers, job shops and manufacturers throughout the world. The company also offers the Behringer Eisele brand of manual, semi-automatic and automatic miter circular cold saws, high performance circular cold saws utilizing bi-metal or carbide saw blades and CNC miter circular sawing systems. Also, the Vernet Behringer line of structural fabricating equipment includes high performance drilling, punching, shearing, notching and marking machines along with beam coping and drilling and sawing lines.
A photo of the Behringer HBM 400 SC High Performance Bandsaw is available at: http://www.behringersaws.com/images/pr/hbm400sc.jpg
SOURCE: PRWeb
View original release here: http://www.prweb.com/releases/behringersaws/high-performance-bandsaws/prweb9078441.htm